XikeStor SKS8300-8X (aka ONTi ONT-S508CL-8S) (aka JT-COM JT-FG6700-8TFM) (aka Hicomdata HK-ES3058-8P-L)

XikeStor SKS8300-8X 8-Ports 10G L3 Managed Switch with 8 SFP+ Slots and 1 Console Port.

These all appear to be packaged version of the Hicomdata HK-ES3058-8P-L

XikeStor SKS8300-8x	ONTi ONT-S508CL-8S	JT-COM JT-FG6700-8TFM

None at this time.

→ Install OpenWrt (generic explanation)

Please add the installation procedure here.

Flash instruction using initramfs image:

1. Prepare TFTP server with an IP address “192.168.2.36”

2. Connect your PC to Port1 on SKS8300-8X

3. Power on SKS8300-8X and interrupt by Ctrl + B

4. Login to the vendor CLI by Ctrl + F and “diagshell_unipoe_env”

5. Login to the U-Boot CLI by “debug_unish_env” command

6. Enable Port1 with the following commands

  rtk 10g 0 fiber1g (or fiber10g if 10GBase-*R)
  rtk ext-devInit 0
  rtk ext-pinSet 2 0

  Note: the last command sets tx-disable to low

7. Download initramfs image from TFTP server

  tftpboot 0x82000000 <image name>

8. Boot with the downloaded image

  bootm

9. On the initramfs image, backup the stock firmware if needed

10. Upload (or download) sysupgrade image to the device

11. Erase “firmware” partition to cleanup JFFS2 of stock FW

  mtd erase firmware

12. Perform sysupgrade with the sysupgrade image 13. Wait ~120 sec to complete flashing

→ generic.sysupgrade

→ generic.debrick

→ failsafe_and_factory_reset

→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

The default network configuration is:

The XikeStor SKS8300-8X has the following buttons:

---- datatemplatelist dttpllist ---- template: meta:template_datatemplatelist cols : Brand, Model, Versions, Device Type, Availability, Supported Since Commit_git, Supported since Rel, Supported current Rel, Unsupported, Bootloader, CPU, Target, CPU MHz, Flash MBs, RAM MB, Switch, Ethernet 100M ports_, Ethernet Gbit ports_, Comments network ports_, Modem, VLAN, WLAN 2.4GHz, WLAN 5.0GHz, WLAN Hardwares, WLAN Comments_, Detachable Antennas_, USB ports_, SATA ports_, Comments USB SATA ports_, Serial, JTAG, LED count, Button count, Power supply, Device Techdata_pageid, Forum topic URL_url, wikidevi URL_url, OEM Device Homepage URL_url, Firmware OEM Stock URL_url, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Comments_ filter : Brand=XikeStor filter : Model=SKS8300-8X filter : Versions=

Front:
Insert photo of front of the casing

Back:
Insert photo of back of the casing

Backside label:
Insert photo of backside label

→ Warranty

Unscrew the two screws on the bottom. You have to break the warranty seal to reach the second screw. Pull back the lower part of the case. This allows access to the upper part of the board.

To get access to the lower part you have to unscrew the three screws on the PCB. Afterwards, you have to slide back the PCB slightly (with some force) to get clearance in the front. You can then carefully lift the PCB.

Main PCB:
Insert photo of PCB

Serial connection parameters for XikeStor SKS8300-8X :

You can tap into I2C communication with the SFPs on the bottom of the board:

→ port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

→ bootloader

None so far.

Space for additional notes, links to forum threads or other resources.

• ...

How to add tags